Electronic Ballasts for Ultraviolet Lamps


Electronic Ballasts for Ultraviolet Lamps

 
Electronic ballasts have almost become the standard in the low pressure lamp lighting industry. They allow energy and financial savings in many applications. The lamp operation is free from flicker and the ballast produces virtually no noise or hum. The incoming 50 Hz power (240 volts) is converted to high-frequency AC (usually 20 to 40 kHz). This leads to a constant gas discharge compared to conventional ballasts and prevents cathode flicker. Electronic ballasts are more efficient than magnetic ballasts in converting input power to the proper lamp power. The operation of low pressure, amalgam ultraviolet UV lamps at higher frequencies reduces end losses, resulting in an overall lamp-ballast system efficiency increase of 15% to 20%. Electronic ballasts are directly interchangeable with magnetic ballasts. They operate with most ultraviolet UV lamps available.Special electronic ballasts can operate two or four lamps reducing the total number of ballasts in a system. This also reduces installation and field wiring costs. Other advantages are reduced weight, less heat and noiseless operation and reduced lamp flicker. Infralight supplies a comprehensive range of ballasts and HID power supplies for low pressure germicidal and medium pressure lamps.
 

Preheat Ballasts for UV lamps

  • Single and dual ultraviolet lamp types available
  • Cable length up to 30m
  • Overtemperature protection
  • Optimized to the specified lamp
  • Status indication by LED and fault relay (volt free)
  • CE approval
Part # Equivalent Part # Supply Voltage (V) Lamp Power (W) Lamp Current (A) Fault Relay Dimensions (mm)
EPS100/425 RH7.425.75 110-240 30-80 0.30-0.425 Yes 185x56x45
EPS100/800 RH7.800.95 110-240 30-95 0.800 Yes 185x56x45
EPS105/1.2 RH7.1200.105 110-240 50-120 1-1.3 Yes 185x56x45
EPS155/1.0 RH8.1000.155 110-240 150-200W 0.8-1.0 Yes 249x65x45
EPS190/1.2 RH8.1200.190 110-240 150-200W 1.2-1.5 Yes 249x65x45
EPS150/1.8 RH8.1800.150 110-240 120-150 1.8-2.0 Yes 249x65x45
EPS200/2.1 RH8.2100.200 110-240 150-210 2.1-2.3 Yes 249x65x45
EPS240/1.8 RH9.1800.240 110-240 220-250 1.8-2.0 Yes 249x106x57
EPS320/2.1 RH9.2100.320 110-240 300-320 2.1-2.3 Yes 249106x57
EPS270/3.8 RH9-3800.270 110-240 250-280 3.6-4.0 Yes 249x106x57
EPS400/3.8 RH9-3800.400 110-240 400 3.8-4.0 Yes 249x106x57
EPS330/4.8 RH9.4800.330 110-240 310-330 4.8-5.0 Yes 249x106x57
electronic ballast wiring diagram preheat lamp ultraviolet lamp electronic ballast
 
      

 

 

Instant and Rapid Start Ballasts for UV Lamps

  • Instant start electronic ballasts for quick lamp start of 2-pin ultraviolet lamps
  • single and dual lamp types available
  • optimized to the specified lamp
  • status indication by LED and relay (volt free)
  • CE approval
Part # Supply Voltage (V) Lamp Power (W) Lamp Current (A) Fault Indication Dimensions (mm)
PI1.425.75 240 30-90 0.30-0.425 Yes 215x44x26
PI1.800.100 240 30-95 0.800 Yes 215X44X26
PI8.1000.155 240 150-200W 0.8-1.0 Yes 249x65x45
PI8.1200.190 240 150-200W 1.2-1.5 Yes 249x65x45
PI8.1800.150 240 120-150 1.8-2.0 Yes 249x65x45
PI8.2100.200 240 150-210 2.1-2.3 Yes 249x65x45
PI9.1800.240 240 220-250 1.8-2.0 Yes 249x106x57
PI9.2100.320 240 300-320 2.1-2.3 Yes 249106x57
PI9-3800.270 240 250-280 3.6-4.0 Yes 249x106x57
PI9-3800.400 240 400 3.8-4.0 Yes 249x106x57
PI9.4800.330 240 310-330 4.8-5.0 Yes 249x106x57

electronic ballast wiring diagram instant start electronic ballast ultraviolet lamps

 

 

We Accept

  • Call to place an order
  • Ask for a quote
  • Inquire for more information